Produkt zum Begriff Preamp:
-
PREAMP-1UP
Unterputz-Vorverstärker
Preis: 257.30 € | Versand*: 0.00 € -
Ampeg Classic Bass Preamp
Analoger Bass Preamp, 3-Band-Klangregelung, Ultra-Hi- und Ultra-Lo-Schalter, True Bypass, Vollmetall-Konstruktion, Betrieb mit Batterie- und Netzteil möglich,
Preis: 118.00 € | Versand*: 0.00 € -
WMD Devices Arcane Preamp
Der Arcane Preamp von WMD ist ein zweistufiges Booster/Fuzz Pedal mit Dreiband-Klangregelung. The WMD Arcane Preamp is a two channel true bypass pedal. The first channel is a medium gain boost that adds a little bit of sparkle and breaks up into a soft overdrive when hit hard. The right footswitch activates the high gain fuzz channel which is fed by the boost and can provide hot lead tones or maximally crunched fuzz. A three band tone stack allows you to sculpt the fuzz tone into just what you want. Click for sound samples. The Controls Left Stomp - This foot switch bypasses or activates the pedal. The Arcane Preamp is wired true bypass, so it won't affect your tone when disengaged. When engaged the blue LED on the left side will be lit. Right Stomp - This foot switch selects the channel. The indicator for the channel select is under the fuzz channel tone controls. The LED will be lit when fuzz channel is active. Boost Gain - The leftmost knob controls the gain of the boost channel. This will add a bit of sparkle and clean gain at medium levels. Crank it to get soft clipping and lots of volume. Boost Level - This controls the output of the boost channel, setting ratios of the gain and level will allow more gain and overdrive without too much level. Or medium gain and maxed level for a big clean boost. Fuzz Gain - When the fuzz channel is engaged, it follows the boost channel. This knob takes the output of the boost and adjusts the level going into the fuzz. This channel has a boatload of gain. Low to medium levels provide touch sensitive distortion, crank it much past half and it starts to crunch. The fuzz channel can provide killer sounding feedback. Bass, Mids, Treble - The amp style tone stack is broken into three bands. Use it to sculpt your fuzz tone. The treble control is very sensitive around the middle with a ton of variation in sound. Fuzz Level - Since the tone stack is all passive, the stack feeds a final amplifier which puts out a ton of level. Use this to level your fuzz tone with the boost tone or to drive your amp's input stage to hell. Battery & 9VDC jack - Use a standard 9V battery inside the pedal for many hours of life, or use a BOSS style power plug (center negative) to power the Arcane Preamp. Warranty - All WMD pedals are warranted against manufacturer defects for one year from date of purchase. Contact WMD if you have any problems. Manual - Click here for the manual. The Arcane Preamp has been reviewed by Premier guitar, check it out . Sound Samples
Preis: 209.00 € | Versand*: 0.00 € -
Okko Cocaine Compressor / Preamp Pedal
The Cocaine features the same optical compressor circuit as its little two-knob brother, the much beloved COCA COMPRESSOR but offers a lot more controls and tone-shaping features.The compression is controlled by two knobs. They do pretts much what their labels say:SUSTAIN adds nothing but clean undistorted sustain to your tone.SQUASH goes from subtle tone-enhancing to a more pronounced compression effect, but even at full tilt it will preserve the attack of your instrument and keep its character.VOLUME allows for a clean boost, unity gain is around 12 o’clock.BASS and TREBLE are active (cut/boost style) controls for an effective tone shaping.The BOOST knob controls an entirely independent circuit, activated by its own footswitch, just like another pedal in the same box. It’s located after the compressor in the signal chain so you can set the comp and eq for your base tone and hit the boost switch for solos (or the other vice versa) . The BOOST knob is something special. Its neutral setting is at 12 o’clock. Turn it to the right for a full-range clean boost or to the left for a lead boost with tighter bass and pronounced mids. The COCAINE is not only a transparent, natural sounding and exceptionally quiet optical compressor, it also serves as a preamp, active equalizer and dual clean boost.Whatever you plug in – electrical guitar or bass, piezo-equipped acoustic guitar (or any other stringed instrument) – the Cocaine will make it sound more balanced, sit better in the mix and generally just... better :-)You’ll probably get addicted soon, hence the name. Like most of our pedals, the COCAINE features an internal voltage doubler for increased headroom and superior dynamic performance.
Preis: 245.00 € | Versand*: 0.00 €
-
Brauche ich einen Preamp?
Ob du einen Preamp benötigst, hängt von deiner spezifischen Situation ab. Ein Preamp kann nützlich sein, wenn du ein Mikrofon oder ein Instrument mit niedrigem Ausgangssignal verwendest und den Pegel erhöhen möchtest, bevor du ihn in dein Aufnahmegerät einspeist. Wenn du jedoch bereits ein Aufnahmegerät hast, das über einen integrierten Preamp verfügt und du mit dem Signal zufrieden bist, ist ein separater Preamp möglicherweise nicht erforderlich.
-
Was ist ein Preamp Gitarre?
Ein Preamp für Gitarre ist ein Gerät, das das elektrische Signal einer Gitarre verstärkt, bevor es an einen Verstärker weitergeleitet wird. Es kann auch dazu verwendet werden, das Signal zu formen und zu modifizieren, um den Klang zu verbessern oder zu verändern. Ein Preamp kann auch dazu beitragen, Rauschen und Störungen zu reduzieren und das Signal sauberer und dynamischer zu machen. Es gibt verschiedene Arten von Preamps, darunter Röhren- und Solid-State-Modelle, die jeweils unterschiedliche Klangcharakteristiken bieten. Ein Preamp kann eine wichtige Rolle dabei spielen, den Klang einer Gitarre zu formen und zu verbessern, insbesondere wenn sie mit anderen Effekten und Verstärkern verwendet wird.
-
Gibt der Preamp zu viel Strom ab?
Es ist möglich, dass der Preamp zu viel Strom abgibt, wenn er nicht ordnungsgemäß funktioniert oder falsch eingestellt ist. Dies kann zu Überlastung oder Beschädigung der angeschlossenen Geräte führen. Es ist wichtig, die Spezifikationen des Preamps zu überprüfen und sicherzustellen, dass er mit den angeschlossenen Geräten kompatibel ist. Bei Bedenken sollte ein Fachmann hinzugezogen werden.
-
Wie stelle ich den Mikrofon-Preamp ein?
Um den Mikrofon-Preamp einzustellen, musst du zunächst den Gain-Regler verwenden, um das Eingangssignal des Mikrofons zu verstärken. Achte darauf, dass der Gain nicht zu hoch eingestellt ist, um Verzerrungen zu vermeiden. Du kannst auch andere Parameter wie Phantomspeisung, EQ oder Kompression anpassen, um den Klang weiter zu optimieren.
Ähnliche Suchbegriffe für Preamp:
-
JHS Pedals The Clover Preamp
Produktdetails effect type: analogue preamp / boost up to 24dB boost 3-band EQ with 15dB boost/cut3-band EQ boost/cut true bypass controls: volume, bass, middle, treble, switches: bypass, no EQ / no mids / full eq input: mono jack output: mono jack metal housing LED status indicator power supply: 9V DC adapter, 100mA (not included) dimensions: 130 x 70 x 60mm weight: 270g made in the USA If you're looking for the distinct, iconic sound of the Boss FA-1 preamp but not quite willing to part with the cash to pay for vintage original, then JHS provide the answer (and a few extras) in the form of The Clover. Think of U2's The Edge in the mid-eighties and you have an idea of the sound this stompbox has been designed to sculpt. However, this pedal should maybe come with a warning, since once you mount it on your board, your setup is likely to change forever: single-coils get fattened up and humbuckers gain enhanced definition, while the heavier stompboxes on your board, as well as any valve amplifiers will benefit from a solid helping of extra power. All because of a lucky little green box. The Clover: A Kind of... Music-Based Homecoming It's not only the electric guitarists of the world who have a lot to gain from this JHS pedal. If your preferred weapon of choice is an acoustic guitar, this convenient preamp/booster will definitely provide a sonic upgrade. The control panel offers power over a three-band equaliser so you can edge closer to the sound of the original pedal that The Clover was born to emulate, while a 3-way switch pot reels it back in by cutting the EQ out completely, filtering out the mids, or opening up the entire range. Click the pot into the No EQ position and this nostalgic pedal is propelled back through time to that authentic Boss preamp-shaped sound. This - along with everything else - confirms The Clover as some kind of ... music-based homecoming! Welcome? If you're looking for the distinct, iconic sound of the Boss FA-1 preamp but not quite willing to part with the cash to pay for vintage original, then JHS provide the answer (and a few extras) in the form of The Clover. Think of U2's The Edge in the mid-eighties and you have an idea of the sound this stompbox has been designed to sculpt. However, this pedal should maybe come with a warning, since once you mount it on your board, your setup is likely to change forever: single-coils get fattened up and humbuckers gain enhanced definition, while the heavier stompboxes on your board, as well as any valve amplifiers will benefit from a solid helping of extra power. All because of a lucky little green box. The Clover: A Kind of... Music-Based Homecoming It's not only the electric guitarists of the world who have a lot to gain from this JHS pedal. If your preferred weapon of choice is an acoustic guitar, this convenient preamp/booster will definitely provide a sonic upgrade. The control panel offers power over a three-band equaliser so you can edge closer to the sound of the original pedal that The Clover was born to emulate, while a 3-way switch pot reels it back in by cutting the EQ out completely, filtering out the mids, or opening up the entire range. Click the pot into the No EQ position and this nostalgic pedal is propelled back through time to that authentic Boss preamp-shaped sound. This - along with everything else - confirms The Clover as some kind of ... music-based homecoming! Welcome?
Preis: 235.00 € | Versand*: 0.00 € -
Dunlop MXR M81 Bass Preamp
Bass Preamp M81 Merkmale: Kombination von Preamp und DI Box für E-Bass Getrennte Regler für Ein- und Ausgang Parametrische Mitten Pre/Post-Schalter entscheidet ob der EQ vor oder nach dem Direct Out greift Regler für Output, Mid. Freq., Input, Bass, Mid und Treble Druckschalter für Ground Lift 2 interne Schalter regeln die Verwendung des Direct Out und ein True Bypass kann geschaltet werden Status LED 6,3mm Klinkenein- und Ausgang XLR-Ausgang Betrieb mit 9V-Batterie oder optionalem Netzadapter (RP NT 1 EU) Made in U.S.A. MXR Bass Innovations Preamp Pedal For studio-quality bass tones wherever you play, rely on the MXR M81 Bass preamp pedal. Separate input and output level controls let you take advantage of MXR's innovative Constant Headroom Technology for clarity at volumes other preamps just can't produce. The flawless direct out can be sent to the house pre or post the 3-band, sweepable midrange EQ section - dial in tone for your amp and leave the PA to the sound chick. To get a new tone from an old bass or amp, or for just a touch of something every now and then, the versatility of the MXR M81 Bass preamp pedal is what you need MXR M81 Bass Preamp Pedal Features: Switchable pre/post EQ direct out - get the right tone for your amp and the room High headroom input and output level controls for distortion-free signal 3-band EQ section with sweepable midrange dials in whatever you need Buffered bypass/True bypass switchable for even greater versatility Operates on 9V battery, optional power supply, pedalboard power, or phantom power from your mixer
Preis: 219.00 € | Versand*: 0.00 € -
Meinl PA-CAJ Cajon Preamp
Robustes Cajon Mikrofon, Lautstärke- und Tone-Regler, 6,3 mm Mono Klinken Ausgang, Hochwertige Signalausgabe, Passt für die meisten Cajons, Inkl. 2 CR2032 3V Knopfzellenbatterien,
Preis: 97.00 € | Versand*: 0.00 € -
OEHLBACH Phono PreAmp Pro, Vorverstärker
Phono PreAmp Pro Verzerrungsarmer Phono-Vorverstärker für Plattenspieler mit MM- oder MC-Tonabnehmer Der Phono PreAmp Pro von Oehlbach integriert Ihren Plattenspieler mit MM- oder MC-Tonabnehmer in bestehende hochwertige HiFi-Komponenten ohne dedizierten Phono-Eingang. Der rauscharme Vorverstärker ist mit vergoldeten Kontakten ausgestattet und ermöglicht eine stabile und sichere Verbindung zwischen dem Phono-Gerät und der HiFi-Anlage. Mit einem externen Netzteil ausgestattet, wiegt der Phono PreAmp Pro gerade einmal 100g und findet dank seiner kompakten Formensprache in jedem HiFi-Rack problemlos Platz. Die einzelnen Komponenten werden über analoge Stereo-Cinch-Anschlüsse verbunden. Features - 24 Karat vergoldete Kontakte - Für Moving-Magnet-Tonabnehmer - Für Moving-Coil-Tonabnehmer - Stromversorgung u?ber externes Netzteil
Preis: 67.99 € | Versand*: 0.00 €
-
Ist ein Interface dasselbe wie ein Preamp?
Nein, ein Interface und ein Preamp sind nicht dasselbe. Ein Interface ist ein Gerät, das Audiosignale von einem Computer aufnimmt und wiedergibt, während ein Preamp ein Gerät ist, das das Eingangssignal eines Mikrofons oder eines anderen Audiogeräts verstärkt, bevor es in ein Aufnahmegerät oder einen Verstärker geht. Ein Interface kann über einen Preamp verfügen, um das Eingangssignal zu verstärken, aber nicht alle Interfaces haben einen integrierten Preamp.
-
Kannst du mir erklären, wie Preamp-Pedale funktionieren?
Preamp-Pedale sind Effektpedale, die das Eingangssignal eines Instruments verstärken und formen, bevor es an den Verstärker weitergeleitet wird. Sie enthalten in der Regel eine Vorverstärkerstufe, die das Signal verstärkt und gleichzeitig den Klang formt, indem sie Höhen, Mitten und Bässe anpasst. Preamp-Pedale können verwendet werden, um den Klang eines Instruments zu verbessern, ihm mehr Sättigung oder Verzerrung hinzuzufügen oder den Ton für verschiedene Musikgenres anzupassen.
-
Ist der Preamp gut für das Rode NT2A?
Ja, der Preamp ist gut für das Rode NT2A. Der Preamp bietet eine saubere und transparente Verstärkung, die das volle Potenzial des Mikrofons ausnutzt. Die Kombination aus dem Preamp und dem Rode NT2A liefert einen klaren und professionellen Klang.
-
Ist ein Preamp für ein USB-Mikrofon sinnvoll?
Ein Preamp für ein USB-Mikrofon kann sinnvoll sein, wenn das Mikrofon einen schwachen Signalpegel hat oder wenn du die Klangqualität verbessern möchtest. Ein Preamp verstärkt das Signal des Mikrofons, sodass es lauter und klarer klingt. Es kann auch helfen, Hintergrundgeräusche zu reduzieren und den Dynamikbereich zu erweitern. Allerdings ist ein Preamp nicht unbedingt erforderlich, da USB-Mikrofone bereits einen integrierten Verstärker haben.
* Alle Preise verstehen sich inklusive der gesetzlichen Mehrwertsteuer und ggf. zuzüglich Versandkosten. Die Angebotsinformationen basieren auf den Angaben des jeweiligen Shops und werden über automatisierte Prozesse aktualisiert. Eine Aktualisierung in Echtzeit findet nicht statt, so dass es im Einzelfall zu Abweichungen kommen kann.